Sikaflex-271 + SikaBooster P-50, Booster-Accelerated Glazing Adhesive, Exterior, Black, Packing: 195 L
Sikaflex-271 + SikaBooster P-50, Booster-Accelerated Glazing Adhesive, Exterior, Black, Packing: 195 L
Sika
Sikaflex-271 + SikaBooster P-50, Booster-Accelerated Glazing Adhesive, Exterior, Black
Sikaflex-271 + SikaBooster P-50, Booster-Accelerated Glazing Adhesive, Exterior, Black
0,00 €
fără TVA
1,00 lei
| Booster accelerated glazing adhesive Sikaflex-271 + SikaBooster P-50 is an accelerated elastic polyurethane adhesive system for glazing applications. Suited for bonding materials relevant for direct glazing such as paints, glass, ceramic frits, painted and e-coated surfaces in commercial-vehicle production. Sikaflex-271 + SikaBooster P-50 is compatible with Sika’s black-primerless bonding process. Owing to the use of SikaBooster it cures largely independently of atmospheric conditions.
| ||||||||||||||||||||||||||||||||||||||||||||||||||||||
PRODUCT BENEFITS
UsageSikaflex-271 + SikaBooster P-50 is designed especially for manual and automated direct-glazing application out of bulk packaging where a fast build-up of adhesion and strength is required. The use of SikaBooster P-50 provides rapid attainment of strength and early adhesion development. Seek manufacturer’s advice and perform tests on original substrates before using Sikaflex-271 + SikaBooster P-50 on materials prone to stress cracking. This product is suitable for experienced professional users only. Tests with actual substrates and conditions have to be performed ensuring adhesion and material compatibility.PackagingSikaflex-271
SikaBooster P-50
| ||||||||||||||||||||||||||||||||||||||||||||||||||||||
Typical Product Data
| ||||||||||||||||||||||||||||||||||||||||||||||||||||||
Technical Information CURE MECHANISM Sikaflex-271 + SikaBooster P-50 cures by reaction with moisture provided by SikaBooster P-50 and largely independent from atmospheric moisture. For typical strength build-up data see table below. Time [h] Tensile lap-shear strength at 23 °C [MPa] 1 1.5 2 4 3 5 Table 1: Strength build-up Sikaflex-271 + SikaBooster P-50 CHEMICAL RESISTANCE Sikaflex-271 + SikaBooster P-50 is generally resistant to fresh water, seawater, diluted acids and diluted caustic solutions; temporarily resistant to fuels, mineral oils, vegetable and animal fats and oils; not resistant to organic acids, glycolic alcohol, concentrated mineral acids and caustic solutions or solvents. | ||||||||||||||||||||||||||||||||||||||||||||||||||||||
Application Information Surface Preparation Surfaces must be clean, dry and free from grease, oil and dust. Surface treatment depends on the specific nature of the substrates and is crucial for a long lasting bond. All pre-treatment steps must be confirmed by preliminary tests on original substrates considering specific conditions in the assembly process. Application Sikaflex-271 + SikaBooster P-50 needs to be processed with an adequate dispensing system. The mixer type needs to be respected (see table Typical Product Data). Sikaflex-271 + SikaBooster P-50 can be applied between 10 °C and 45 °C but changes in reactivity and application properties have to be considered. The optimum temperature for substrate and sealant is between 15 °C and 25 °C. To ensure a uniform thickness of the bondline it is recommend to apply the adhesive in form of a triangular bead (see figure 1).
Figure 1: Recommended bead configuration
The open time is significantly shorter in hot and humid climate. The glass must always be joint within the open time. Never install a glass after the product has built a skin. As a rule of thumb, a change of + 10 °C reduces the open time by half. Removal Uncured Sikaflex-271 + SikaBooster P-50 can be removed from tools and equipment with Sika Remover-208 or another suitable solvent. Once cured, the material can only be removed mechanically. Hands and exposed skin have to be washed immediately using hand wipes such as Sika Cleaner-350H or a suitable industrial hand cleaner and water. Do not use solvents on skin. |
The above design is only a sample of the options available, for reference purposes only. Our policy of continuous improvement may result in a change of specifications without notice. If any discrepencies might be between the data sheet values and standards, we reserve the rights to make technical changes. Our company will not be held responsible, as all or any of pictures, drawings, weights and dimensions details or other elements in this document are only indicative and must not be considered contractual. Contact our sales team for other specifications or custom made products.
Contact our sales team for other specifications or custom made products.