Three component, PMMA based self-levelling mortar Sikalastic Rapid Levelling Mortar is used as a protective layer, thick film coating or equalising mortar.
As part of Sikalastic Rapid Trafficable (Waterproofing & Wearing) System it protects the waterproofing layer against the impact of foot traffic on account of its load distributing effect (protective layer). In the case of areas that are either free from cracks or have only hairline cracks, it is used as a thick film coating without the waterproofing layer as part of the Sikalastic Rapid Trafficable (Wearing System). Furthermore it is used as an equalising mortar to level out areas of damage and up to 10mm height differences. - Fast-curing
- Easy and fast application
- Cold applied
- Solvent-free
- Seamless membrane
|
Usage - Protective layer, thick film coating or equalising mortar for SikalasticRapid Trafficable systems
- For new construction and refurbishment projects
Advantages - Fast-curing
- Easy and fast application
- Cold applied
- Solvent-free
- Seamless membrane
Packaging | SUMMER | | | Sikalastic Rapid Levelling Mortar Resin | 10 Kg | | Sikalastic Rapid Levelling Mortar Powder | 23 Kg | | Sikalastic Rapid Catalyst | 2x0.1 Kg | | Total | 33.20 Kg |
| WINTER | | | Sikalastic Rapid Levelling Mortar Resin | 10 Kg | | Sikalastic Rapid Levelling Mortar Powder | 23 Kg | | Sikalastic Rapid Catalyst | 4x0.1 Kg | | Total | 33.40 Kg |
Colour RAL 7032 (Pebble Grey) |
Application Information Ambient Air Temperature +3 °C min. / +35 °C max. Relative Air Humidity The relative humidity must be ≤90% Dew Point Beware of condensation. Surface temperature during application and cure must be a minimum of 3°C above dew point.
The substrate temperature must not be less than +3°C if a topping is applied to the surface. Reaction problems can occur at lower temperatures. Substrate Temperature +3 °C min. / +50 °C max. Substrate Moisture Content The surface to be coated must be dry and ice-free
The surface must be protected from moisture until the coating has hardened Pot Life The material in opened containers should be applied immediately
At 20°C, 2% catalyst the pot life is approximately 15 minutes Curing Time | Temperature | Catalyst | Rain Resistant | Can be
trafficked/
overcoate | Full Cure | | 20°C | 2% | 30 minutes | 1 hour | 3 hours |
Note: Times are approximate and will be affected by changing ambient conditions.
Higher temperatures or greater proportions of Sikalastic Rapid Catalyst will reduce reaction times, while lower temperatures and smaller proportions of Catalyst will increase reaction times.
The following table indicates the recommended amount of Sikalastic Rapid Catalyst required to adjust the curing reaction to the temperature. Substrate temperature in °C; required amounts of Sikalastic Rapid Catalyst in % w/w (guide) | -5 | +3 | 5 | 10 | 15 | | N/A | 6% | 6% | 4% | 4% | | 20 | 25 | 30 | 35 | 40 | | 2% | 2% | 2% | 2% | 1% | | 45 | 50 | | | | | 1% | 1% | | | |
Return-to-service times are provided as a guide only and may vary as a result of conditions. Newly installed balconies should be protected from exposure to heavy traffic by overlaying with an appropriate protective covering. This is particularly critical where early access is needed by other construction related traffic. Sika Liquid Plastics will not be held responsible for damage to balcony surfaces that results from failures to adequately protect newly laid areas.
For further advice, consult Sika Liquid Plastics Technical Customer Services |
The above design is only a sample of the options available, for reference purposes only. Our policy of continuous improvement may result in a change of specifications without notice. If any discrepencies might be between the data sheet values and standards, we reserve the rights to make technical changes. Our company will not be held responsible, as all or any of pictures, drawings, weights and dimensions details or other elements in this document are only indicative and must not be considered contractual. Contact our sales team for other specifications or custom made products.
Contact our sales team for other specifications or custom made products.
