Chat
Produse
Autentificare
0 Favorite
  • Products
  • Sikafloor-306 W, Matt Polyurethane Seal Coat for Comfortfloor Systems, Interior, Yellowish, 10 Kg

Sikafloor-306 W, Matt Polyurethane Seal Coat for Comfortfloor Systems, Interior, Yellowish, 10 Kg

Cod produs: PTG259.00100
Share

Sikafloor-306 W, Matt Polyurethane Seal Coat for Comfortfloor Systems, Interior, Yellowish, 10 Kg

Cod produs: PTG259.00100
Share
Sika
Sika este un lider global în domeniul materialelor chimice speciale pentru construcții și industrie. Compania dezvoltă și furnizează produse și sisteme inovatoare pentru lipire, etanșare, amortizare, întărire și protecție a structurilor. Cu un accent puternic pe sustenabilitate și performanță, Sika deservește o gamă largă de aplicații, inclusiv producția de beton, hidroizolații, acoperișuri, pardoseli și consolidări structurale.
Citește tot

Sikafloor-306 W, Matt Polyurethane Seal Coat for Comfortfloor Systems, Interior, Yellowish, 10 Kg

Această combinație nu există.

Cere ofertă Cere ofertă
    Product Image
    Sikafloor-306 W, Matt Polyurethane Seal Coat for Comfortfloor Systems, Interior, Yellowish, 10 Kg

    0,00 € fără TVA 0.0 EUR

    1,00 lei

    Add to Cart

    2-PART PUR MATT SEAL COAT PART OF THE SIKA COMFORTFLOOR FLOORING RANGE

    Sikafloor-306 W is a two part water based, very low VOC, polyurethane, matt seal coat.

    • Water based
    • Very low odour
    • Good UV and yellowing resistance
    • Easy to clean
    Usage
    Matt seal coat for Sika ComfortFloor flooring range  
    Advantages
    • Water based
    • Very low odour
    • Good UV and yellowing resistance
    • Easy to clean
    Packaging

    Part A

    8.5 Kg

    Part B

    1.5 Kg

    Part A+B

    10 Kg
    Colour

    Part A

    white, liquid

    Part B

    yellowish, liquid

    Sikafloor-306 W is matt after final curing.
    Technical Information
    Abrasion Resistance

    ~11 mg

    CS10 /1000/1000

    Tensile Strength

    ~ 18 MPa (14 days / +23 °C)

    (DIN 53504)

    Chemical Resistance

    Sikafloor-306 W is resistant to many chemicals. Contact Sika technical service for specific information.
    Application Information
    Mixing Ratio

    Part A : Part B = 85 : 15 (by weight)
    Ambient Air Temperature

    +10 °C min. / +30 °C max.
    Relative Air Humidity

    75 % max.
    During curing the humidity should not exceed 75 % max. Adequate fresh air ventilation must be provided to remove the excess moisture from the curing
    product.
    Dew Point

    Be aware of condensation!

    The substrate and uncured floor must be at least 3 °C above dew point to reduce the risk of condensation or blooming on the floor finish.
    Substrate Temperature

    +10 °C min. / +30 °C max.
    Pot Life

    Temperature

    Time

    +10 °C

    ~ 50 minutes

    +20 °C

    ~ 30 minutes

    +30 °C~ 20 minutes

    Caution: End of potlife is not noticeable.
    Curing Time

    Before overcoating Sikafloor-306 W allow:

    Substrate temperature

    Minimum

    Maximum

    +10 °C

    26 hours

    4 days

    +20 °C

    16 hours

    3 days

    +30 °C

    12 hours

    2 days

    Based on relative humidity of max. 75 % and good ventilation. Times are approximate and will be affected by changing ambient conditions particularly temperature and relative humidity.
    Applied Product Ready for Use

    Temperature

    Foot traffic

    Light traffic

    Full cure

    +10 °C

    ~ 30 hours

    ~ 48 hours

    ~ 6 days

    +20 °C

    ~ 16 hours

    ~ 24 hours

    ~ 4 days

    +30 °C

    ~ 12 hours

    ~ 18 hours

    ~ 3 days

    Note: Times are approximate and will be affected by changing ambient conditions

    The above design is only a sample of the options available, for reference purposes only. Our policy of continuous improvement may result in a change of specifications without notice. If any discrepencies might be between the data sheet values and standards, we reserve the rights to make technical changes. Our company will not be held responsible, as all or any of pictures, drawings, weights and dimensions details or other elements in this document are only indicative and must not be considered contractual. Contact our sales team for other specifications or custom made products.

    Contact our sales team for other specifications or custom made products.
    Vezi Fisa Tehnica
    Descarca Fisa Tehnica
    General Specifications
    Packaging Part A: 8.5 kg; Part B: 1.5 kg; Part A + B: 10 kg
    Chemical Base Polyurethane
    Usage Matt seal coat for ComfortFloor systems
    Application Method Roller
    Usage Area Interior
    Color Yellowish
    Ambient Air Temperature +10 °C min. / +30 °C max.
    Storage Conditions The product must be stored properly in original, unopened and undamaged sealed packaging, in dry conditions at temperatures between +5 °C and +30 °C.
    Curing Time +10 °C 26 hours; +20 °C 16 hours; +30 °C 12 hours
    Working Time +10 °C ~ 50 minutes; +20 °C ~ 30 minutes; +30 °C ~ 20 minutes
    Density Part A: 1.05 kg/L; Part B: 1.13 kg/L; Mixed resin: 1.07 kg/L (diluted with 5–10% water)
    Consumption 0.13 kg/m²/layer
    Aceasta este o previzualizare a produselor vizualizate recent de către utilizator. Odată ce utilizatorul a văzut cel puțin un produs, acest fragment va fi vizibil.

    Produse Recent Vizualizate