Self-leveling decorative resin with low thermal conductivity Sikafloor Marine-595 is a self-levelling aliphatic 2-component polyurethane decorative floor resin. It is part of the Sikafloor Marine Deco systems for exterior use.
If the Sikafloor Marine-595 needs to be accelerated, Sikafloor Marine-001 or -002 can be used. - Good application characteristics
- Low thermal conductivity
- Low density
- Patented Sika Cool technology
- Solvent-free
- Longterm elastic
- Very high yellowing resistance
- Very low VOC emission
- Acceleration option available
|
PRODUCT BENEFITS - Good application characteristics
- Low thermal conductivity
- Low density
- Patented Sika Cool technology
- Solvent-free
- Longterm elastic
- Very high yellowing resistance
- Very low VOC emission
- Acceleration option available
Usage Sikafloor Marine-595 is designed as part of the Sikafloor Marine Deco systems as synthetic teak decking solution with patented Sika Cool Technology, for external decks in shipbuilding, cruise and leisure boat construction. This product is suitable for experienced professional users only. Tests with actual substrates and conditions have to be performed ensuring workability, adhesion and material compatibility. Packaging Sikafloor Marine-595 (A) Sikafloor Marine-595 (B) Sikafloor Marine-001/002 |
Typical Product Data| Solid content | | 100 % | | Mixing ratio | by weight | 41 : 25 | | Application temperature | substrate / climate | 15 ─ 30 °C A, B | | Shore A hardness (CQP023-1 / ISO 48-4) | | 90 | | Tensile strength (DIN 53504) | | 8.5 MPa | | Elongation at break (DIN 53504) | | 50 % | | Pot-life | 15 °C20 °C30 °C | 120 minutes 90 minutes 60 minutes |
| Sikafloor Marine-595 (A) | Sikafloor Marine-595 (B) |
|
Technical Information CURE MECHANISM The curing of Sikafloor Marine-595 takes place by a chemical reaction of the two components.
Higher temperatures speed up and lower temperatures slow down the curing process.
CHEMICAL RESISTANCE For advice contact the Technical Department of Sika Industry.
|
Application Information Surface Preparation Sikafloor Marine-595 is installed on top of the deck levelling compound.
Metallic decks need to be prepared to SA 2.5 (ISO 8501). Aluminium decks must not be shot blasted. The prepared metallic surfaces need to be clean, free of dirt, grease, oil and loose particles before the SikaCor ZP Primer is applied.
The application area must be protected against weather and direct sunlight. Application Sikafloor Marine-595 is poured and spread evenly by means of a notched trowel, flat trowel or pin-rake. In critical areas a spike roller can be used to improve levelling and de-airing. For deeper sections (e.g. unevenness), it might be necessary to pre-level these sections. Ensure the pre-leveled sections have achieved "foot traffic" cure level prior to proceeding. For liquid application on cambers and slopes multiple applications steps may be needed. Curing speed depends on temperature and layer thickness. Always consider the pot life to keep a wet edge.
Prior to application, always consult the most current Application Manual. Curing Indications regarding curing details see table below: | Tempera-
ture | Foot traffic | Light trafficA | Full cure | | 15 °C | 16 hours | 32 hours | 48 hours | | 20 °C | 12 hours | 16 hours | 48 hours | | 30 °C | 8 hours | 12 hours | 24 hours |
A) food trolleys and light rolling equipment on soft wheels Removal Uncured Sikafloor Marine-595 can be removed from tools and equipment with Sika Colma Cleaner or another suitable solvent. Once cured, the material can only be removed mechanically. Hands and exposed skin shall be washed immediately using hand wipes such as Sika Cleaner-350H or a suitable industrial hand cleaner and water. Do not use solvents on skin. Application Limits Freshly applied Sikafloor Marine-595 must be protected from moisture, condensation and water for at least 1 day. Uncured material reacts in contact with water (foaming). STORAGE CONDITIONS Both components of Sikafloor Marine-595 have to be kept between 5 °C and 30 °C in a dry place. Do not expose it to direct sunlight. After opening of the packaging, the contents need to be protected against moisture. Minimum temperature during transportation is 5 °C. |
The above design is only a sample of the options available, for reference purposes only. Our policy of continuous improvement may result in a change of specifications without notice. If any discrepencies might be between the data sheet values and standards, we reserve the rights to make technical changes. Our company will not be held responsible, as all or any of pictures, drawings, weights and dimensions details or other elements in this document are only indicative and must not be considered contractual. Contact our sales team for other specifications or custom made products.
Contact our sales team for other specifications or custom made products.
