Pigmented, solvent-based Primer for various substrates Sika® Primer-207 is a solvent-based black primer, which reacts with moisture and forms a thin layer. This layer acts as a link between substrates and adhesives.
Sika® Primer-207 is specifically formulated for the treatment of bond faces prior to application of Sika’s 1-component Polyurethanes. This primer might provide excellent adhesion without previous activation step on many substrates. Sika® Primer-207 fluoresces under long-wave UV light for a limited period of time. This feature is used for in-process control. - Enhanced adhesion on a wide variety of substrates
- Visible under UV light
- Easy to use
|
Product Benefits - Enhanced adhesion on a wide variety of substrates
- Visible under UV light
- Easy to use
Usage Sika® Primer-207 is used to improve adhesion on a very broad range of different substrates such as float glass, ceramic-coated glass, plastics, pre-coatings, painted surfaces, E-coats and metals.
Seek manufacturer’s advice and perform tests on original substrates before using Sika® Primer-207 on materials prone to stress cracking.
This product is suitable for experienced professional users only. Tests with actual substrates and conditions have to be performed to ensure adhesion and material compatibility. Advantages - Enhanced adhesion on a wide variety of substrates
- Visible under UV light
- Easy to use
|
Typical Product Data| Chemical base | | Solvent-based Polyurethane solution | | Colour (CQP001-1) | | Black | | Solid content | | 27 % | | Application temperature | | 5 ─ 40 °C | | Application method | | Brush, felt or foam applicator | | Consumption | depending on substrate porosity | 50 ml/m2 | | Flash-off time | above 5 °Cmaximum | 10 minutes A 24 hours A | | Shelf life | 1000 mlsmaller packagings | 9 months B 12 months B |
| CQP = Corporate Quality Procedure | A)for specific application, temperature and flash-off time may be different | | B)stored in sealed container in up-right position in a dry place ≤ 25 °C |
|
Technical Information IMPORTANT NOTE If Sika® Primer-207 is used below 5 °C further testing under expected conditions are mandatory.
Sika® Primer-207 is a moisture reactive system. In order to maintain product quality it is important to reseal the container with the inner plastic liner immediately after use. Once the surface pre-treatment operation is completed, the cap has to be screwed on. Dispose of product one month after opening if used frequently or after two months in case of infrequent use. For 100 ml pack sizes dispose it of two weeks after opening. 30 ml cans, stix and tubes are for single application only. If gelling, separation or a significant increase in viscosity is noted, discard the primer immediately.
Never dilute or mix this product with any other substances.
If used on transparent or translucent substrates such as float glass, plastics, etc., an adequate UV protection is mandatory.
DETECTION OF THE LUMINESCENCE Sika® Primer-207 can be visualized by using a light source with a wavelength of 320 to 420 nm as inline control. By reducing foreign light such as sunlight or artificial light during the detecting process the quality of the detection can be increased significantly.
Note: The luminescent effect will degrade with time.
|
Application Information METHOD OF APPLICATION Surfaces must be clean, dry and free from grease, oil, dust and contaminants.
Adhesion on substrates may be improved by adding and/or combining pre-treatment processes such as scuffing, cleaning and activating. Application Shake the Sika® Primer-207 can very thoroughly until mixing balls rattle freely. Continue shaking for another minute and apply a thin but covering coat with a brush, felt or foam applicator.
Ideal application and surface temperature are between 15 °C and 25 °C.
Sika® Primer-207 has to be applied once only. Care must be taken to ensure that this single application gives adequately dense coverage. Consumption and method of application depend on the specific nature of the substrates. Tightly reseal container immediately after each use. |
The above design is only a sample of the options available, for reference purposes only. Our policy of continuous improvement may result in a change of specifications without notice. If any discrepencies might be between the data sheet values and standards, we reserve the rights to make technical changes. Our company will not be held responsible, as all or any of pictures, drawings, weights and dimensions details or other elements in this document are only indicative and must not be considered contractual. Contact our sales team for other specifications or custom made products.
Contact our sales team for other specifications or custom made products.
