| Sikafloor®-10 Pronto is a 4-part, low-viscosity, fast curing primer based on reactive acrylic resins with enhanced substrate adhesion for the Sikafloor®-Pronto Modular System. - Very fast curing, even at low temperatures
- Enhanced adhesion for ceramic substrates or metal
- Solvent-free
- Part of a complete modular system
|
Usage - Fast curing, low viscosity primer with enhanced adhesion for difficult substrates such as dense concrete, tiles, asphalt or steel
Advantages - Very fast curing, even at low temperatures
- Enhanced adhesion for ceramic substrates or metal
- Solvent-free
- Part of a complete modular system
Packaging Part A | Sikafloor®-10 Pronto | 21.2 kg containers, 200 kg drums | Part B | Sika®-Pronto Hardener | 1.0 kg packs (in 0.1 kg bags) | Part C | Sikafloor®-Pronto AP 1 | 8.0 kg metal cans | | Part D | Sikafloor®-Pronto AP 2 | transparent |
Colour Part A | Sikafloor®-10 Pronto | transparent, liquid | Part B | Sika®-Pronto Hardener | white, powder | Part C | Sikafloor®-Pronto AP 1 | transparent | | Part D | Sikafloor®-Pronto AP 2 | transparent |
|
Technical Information Thermal Resistance Exposure* | Dry heat | Permanent | +50°C | Short-term max. 2 d | +60°C | | Short-term max. 1 h | +80°C |
Short-term heat* up to +80°C where exposure is only occasional (steam cleaning etc.)
*No simultaneous chemical and mechanical exposure and only in combination with Sikafloor®-14 / -16 or - 15 / -17 or -32 / -18 Pronto as a broadcast system with approx. 3 - 4 mm thickness.
|
Application Information Mixing Ratio For mixing guidelines please refer to the Table 1 and 2 below.
Table 1: Typical mixture of Sikafloor® -10 Pronto
| Part A
Sikafloor®-10 Pronto | Part C
Sikafloor®-Pronto AP 1 | Part D
Sikafloor®-Pronto AP 2 | | 42.4 kg (2 units) | 8 kg | 0.1 kg | | 21.2 kg (1 unit) | 4 kg | 0.05 kg | | 10.6 kg (1/2 unit) | 2 kg | 0.025 kg |
Table 2: The amount of Hardener required to be added on 21.2 kg Sikafloor®-10 Pronto is dependent on the ambient- and substrate temperature. | Temperature | Sikafloor®-Pronto Hardener (% pbw) for the system A+B+AP1+AP2 | Sikafloor®-Pronto Hardener (% pbw) for the system A+B+AP1 | | 0°C | 1.270 g
(6.0%) | 1.058 g
(5.0%) | | +10°C | 1.060 g
(5.0%) | 848 g
(4.0%) | | +20°C | 850 g
(4.0%) | 638 g
(3.0%) | | +30°C | 640 g
(3.0%) | 425 g
(2.0%) |
The hardener powder can also be supplied by Sika under the product name "Perkadox CH 50 X“ Ambient Air Temperature 0°C min. / +30°C max. Relative Air Humidity 80% r.h. max. Dew Point Beware of condensation!
The substrate and uncured floor must be at least 3°C above dew point to reduce the risk of condensation or blooming on the floor finish. Substrate Temperature 0°C min. / +30°C max. Substrate Moisture Content ≤ 4% pbw moisture content.
Test method: Sika-Tramex or CM.
No rising moisture according to ASTM (Polyethylene-Sheet). Pot Life Temperature | Time | +0°C | ~ 20 minutes | +10°C | ~ 15 minutes | | +20°C | ~ 15 minutes | | +30°C | ~ 10 minutes |
Curing Time Before applying Sikafloor®-10 / -14 / -15 / -32 Pronto on Sikafloor®-10 Pronto allow: Substrate temperature | Minimum | Maximum | +0°C | 70 minutes | 48 hours | +10°C | 50 minutes | 36 hours | | +20°C | 50 minutes | 24 hours | | +30°C | 35 minutes | 24 hours |
Times are approximate and will be affected by changing ambient conditions particularly temperature and relative humidity. Applied Product Ready for Use Termperature | Foot traffic | Full cure | | +0°C | 70 minutes | ~ 2 hours | | +10°C | 50 minutes | ~ 2 hours | | +20°C | 50 minutes | ~ 2 hours | | +30°C | 35 minutes | ~ 2 hours |
Note: Times are approximate and will be effected by changing ambient conditions. |
The above design is only a sample of the options available, for reference purposes only. Our policy of continuous improvement may result in a change of specifications without notice. If any discrepencies might be between the data sheet values and standards, we reserve the rights to make technical changes. Our company will not be held responsible, as all or any of pictures, drawings, weights and dimensions details or other elements in this document are only indicative and must not be considered contractual. Contact our sales team for other specifications or custom made products.
Contact our sales team for other specifications or custom made products.
