Epoxy high performance chemical anchoring adhesive Sika AnchorFix-3030 is an epoxy resin based, two-part, thixotropic, high performance anchoring adhesive for anchoring threaded rods and reinforcing bars in both cracked and uncracked dry or damp concrete. - Long open-time.
- Can be used in damp concrete.
- High load capacity.
- ETA for anchoring in cracked concrete.
- ETA for post installed rebar connections.
- Seismic tested (C1 & C2).
- Suitable for contact with drinking water.
- Fire resistant.
- Styrene-free.
- Good adhesion to substrates.
- Shrinkage-free hardening.
- Low emissions.
- Low wastage.
|
Usage Anchoring adhesive for fixing of non-expanding anchors in the following:
Structural work- Rebar / steel reinforcement anchoring in new and refurbishment works
- Threaded rods
- Bolts and special fastening / fixing systems
Metalwork and carpentry- Handrails, balustrades and supports
- Railings
- Window and door frames
Substrates- Concrete (cracked and uncracked)
- Hollow and solid masonry
- Wood
- Natural and reconstituted stone
- Solid rock
Advantages - Long open-time.
- Can be used in damp concrete.
- High load capacity.
- ETA for anchoring in cracked concrete.
- ETA for post installed rebar connections.
- Seismic tested (C1 & C2).
- Suitable for contact with drinking water.
- Fire resistant.
- Styrene-free.
- Good adhesion to substrates.
- Shrinkage-free hardening.
- Low emissions.
- Low wastage.
Packaging | 385 ml dual cartridge | 12 cartridges per box Pallet: 70 boxes with 840 cartridges | | 585 ml dual cartridge | 12 cartridges per box Pallet: 44 boxes with 528 cartridges |
Refer to current price list for packaging variations. Colour | Part A | Off white | | Part B | Grey | | A+B mixed | Light grey |
|
Technical Information Compressive Strength | ~95 N/mm2 (7 days, +20 °C) | (ASTM D 695) |
Flexural Strength | ~45 N/mm2 (7 days, +20 °C) | (ASTM D 790) |
Tensile Strength | ~23 N/mm2 (7 days, +20 °C) | (ASTM D 638) |
Service Temperature | Long term | -40 °C min. / +50 °C max. | | Short term (1–2 hours) | +70 °C |
|
Application Information Mixing Ratio Part A : Part B = 3 : 1 by volume Layer Thickness ~8 mm maximum Sag Flow Non-sag, including overhead Product Temperature +10 °C minimum / +40 °C maximum Ambient Air Temperature +5 °C minimum / +40 °C maximum Dew Point Beware of condensation.
Substrate temperature during application must be at least +3 °C above dew point. Substrate Temperature +5 °C minimum / +40 °C maximum Curing Time | Temperature | Open time - Tgel | Curing time - Tcur | | +35 °C to +40 °C | 6 minutes | 2 hours | | +30 °C to +35 °C | 8 minutes | 4 hours | | +25 °C to +30 °C | 12 minutes | 6 hours | | +20 °C to +25 °C | 18 minutes | 8 hours | | +15 °C to +20 °C | 25 minutes | 12 hours | | +10 °C to +15 °C | 40 minutes | 18 hours | | +5 °C to +10 °C* | 150 minutes | 24 hours | | +5 °C* | 300 minutes | 24 hours |
* Minimum cartridge temperature: +10 °C |
The above design is only a sample of the options available, for reference purposes only. Our policy of continuous improvement may result in a change of specifications without notice. If any discrepencies might be between the data sheet values and standards, we reserve the rights to make technical changes. Our company will not be held responsible, as all or any of pictures, drawings, weights and dimensions details or other elements in this document are only indicative and must not be considered contractual. Contact our sales team for other specifications or custom made products.
Contact our sales team for other specifications or custom made products.
