Styrene-free anchoring adhesive for medium to high loads Solvent and styrene-free, epoxy acrylate based, 2-component anchoring adhesive for normal / moderate climate conditions. - Fast curing.
- Standard guns can be used for application.
- High load capacity.
- ETA to ETAG 001 for anchoring in concrete.
- ETA to ETAG 001 for rebar connections.
- Suitable for cracked concrete.
- Drinking Water certified.
- LEED Attestation available.
- Non-sag, even overhead.
- Styrene-free.
- Low odour.
- Low wastage.
- Suitable in wet / damp (but clean) holes.
- Appropriate for marine enviroments.
|
Usage As a fast curing anchoring adhesive for all grades of: - Rebars / reinforcing steel
- Threaded rods
- Bolts and special fastening systems
- Concrete (cracked and non-cracked)
- Solid masonry
- Steel
- Hard natural stone*
- Solid rock*
* These substrates may vary greatly, in particular with regard to strength, composition and porosity. Therefore, for each application the suitability of Sika AnchorFix-2+ Adhesive must be tested by first applying the product to a sample area. In particular, check bond strength, surface staining and discoloration. Advantages - Fast curing.
- Standard guns can be used for application.
- High load capacity.
- ETA to ETAG 001 for anchoring in concrete.
- ETA to ETAG 001 for rebar connections.
- Suitable for cracked concrete.
- Drinking Water certified.
- LEED Attestation available.
- Non-sag, even overhead.
- Styrene-free.
- Low odour.
- Low wastage.
- Suitable in wet / damp (but clean) holes.
- Appropriate for marine enviroments.
Packaging | 300 ml standard cartridge | 12 cartridges per box | | 1 pallet: 75 boxes | | |
Colour Component A: white
Component B: black
Component A+B mixed: grey |
Technical Information Compressive Strength | ~70 N/mm2 (7 days, +20 °C) | (ASTM D 695) |
Modulus of Elasticity in Compression | ~7 000 N/mm2 (7 days, +20 °C) | (ASTM D 695) |
Flexural Strength | ~29 N/mm2 (7 days, +20 °C) | (ASTM D 790) |
Tensile Strength | ~15 N/mm2 (7 days, +20 °C) | (ASTM D 638) |
Service Temperature | Long term | -40 °C min. / +50 °C max | | Short term (1–2 hours) | +80 °C |
|
Application Information Mixing Ratio Component A : Component B = 10 : 1 by volume Layer Thickness ~5 mm max. Sag Flow Non-sag, even overhead Product Temperature Sika AnchorFix-2+ must be at a temperature of between +5 °C and +30 °C for application. Ambient Air Temperature +5 °C min. / +30 °C max. Dew Point Beware of condensation.
Substrate temperature during application must be at least 3 °C above dew point. Substrate Temperature +5 °C min. / +30 °C max. Curing Time | Temperature | Open time - Tgel | Curing time - Tcur | | +25 °C to +30 °C | 4 minutes | 40 minutes | | +20 °C to +25 °C | 5 minutes | 50 minutes | | +15 °C to +20 °C | 6 minutes | 75 minutes | | +10 °C to +15 °C | 8 minutes | 85 minutes | | +5 °C to +10 °C* | 10 minutes | 145 minutes |
*Minimum cartridge temperature = +5 °C |
The above design is only a sample of the options available, for reference purposes only. Our policy of continuous improvement may result in a change of specifications without notice. If any discrepencies might be between the data sheet values and standards, we reserve the rights to make technical changes. Our company will not be held responsible, as all or any of pictures, drawings, weights and dimensions details or other elements in this document are only indicative and must not be considered contractual. Contact our sales team for other specifications or custom made products.
Contact our sales team for other specifications or custom made products.
