Sikafloor Level-30, Industrial Self-Leveling Screed
SIKA
Sika is a global leader in specialty chemicals for the construction and industrial sectors. The company develops and supplies innovative products and systems for bonding, sealing, damping, reinforcing, and protecting structures. With a strong focus on sustainability and performance, Sika serves a wide range of applications including concrete production, waterproofing, roofing, flooring, and structural strengthening.
Read moreHigh performance, self levelling and fast drying, cementitious screed for interior or exterior in 4 – 30 mm (0.157 – 1.18 in) Sikafloor® Level-30 is a polymer modified, pumpable, self levelling fast drying cementitious screed for higher thickness interior or exterior floors, meeting the requirements of class R3 according to EN 1504-3. | ||||||||||||||||||||||||||||||||||||||||||
UsageSikafloor® Level-30 is an floor self levelling screed to level or smooth screeds and concrete floors at a thickness between 4–30mm (0.157–1.18 in) in one working step. Sikafloor® Level-30 is useable as screed for industrial service conditions when sealed with a PU or EP resin top coat from medium to high load (heavy-traffic + forklift pallet truck with impact load ) Sikafloor® Level-30 is also suitable for filling, smoothing and levelling of suitable substrates before applying parquet, ceramic tiles, seamless resinfloors, textile, elastic floor coverings Sikafloor® Level-30 is useable as screed for exterior areas when sealed with a covering e.g. a coating.
Advantages
Packaging25 kg (55.1 lb) bags ColourPowder - beige-grey | ||||||||||||||||||||||||||||||||||||||||||
Typical Product Data
| ||||||||||||||||||||||||||||||||||||||||||
ApplicationMixing Ratio 5 to 5.25 L (1.39 gal) water for 25 kg (55.1 lb) Sikafloor® Level-30 Layer Thickness 4 - 30 mm (0.157 - 1.18 in) Ambient Air Temperature ≥ +10 °C (+50 °F) and ≤ +25 °C (+77 °F) Relative Air Humidity < 75 % Substrate Temperature ≥ +10 °C (+50 °F) and ≤ +25 °C (+77 °F) Substrate Pre-Treatment Normal intended use of the floor The one part acrylic primer Sikafloor®-01 Primer is recommended for a pore free surface with very good surface adhesion. Refer to the relevant PDS for the recommended application details etc. High loads intended use of the floor Priming with epoxy resins such as Sikafloor® -155WN, Sikafloor® -150 or Sikafloor® -151 fully broadcast with quartz sand 0.3–0.8 mm (0.0118–0.0315 in). Pot Life
The temperature will affect the pot life. Application at temperatures above +23 °C (+73 °F) will reduce the pot life and the working time. Temperatures below +23 °C (+73 °F) will increase the pot life and extend the working time. Waiting Time / Overcoating
When overcoating Sikafloor® Level-30 always ensure the moisture content has achieved the required value for the coating product, as the waiting time will vary with the application thickness and ambient humidity. (Refer to the coating product data sheet) Applied Product Ready for Use At +20 °C (+68 °F) and 50% r.h.
Note: Times are approximate and will be affected by changing substrate and ambient conditions, particularly the temperature and relative humidity. Consumption ~ 1.8 kg/m 2 /mm MIXING By Hand For 25 kg (55.1 lb) Sikafloor® Level-30 is required 5 to 5.25 l water. When mixing manually add the dry powder (25 kg (55.1 lb)) into a container with the clean water. Mix thoroughly for a minimum of 3 minutes, by use of an electric stirrer, recommended is the use of a double disc stirring paddle or a spiral mix paddle (< 500 rpm). maturing time: After mixing leave the material to stand in the container for ~ 2 minutes until the majority of air bubbles have dispersed. Pumping When using a mortar pump with appropriate equipment (Putzmeister MP 20/25, DuoMix 2000 or PFT G5 FE) set the machine in a way that a uniform mixture is achieved. The use of a remixer is recommended. Control the water dosage to achieve the required flow, measuring the final average flow diameter on a flat, clean, dry flow table.
APPLICATION Pour the mixed material onto the primed surface and apply by trowel or pin screed rake to the required thickness. Roll thoroughly with a spiked roller in two directions to remove any entrapped air. Best application time would be during falling temperatures. CLEANING OF TOOLS Clean all tools and application equipment with water immediately after use. Hardened / cured material can only be removed mechanically. |