| Sikafloor-262 AS N is a two part, self-smoothing, coloured epoxy resin coating. "Total solid epoxy composition acc. to the test method Deutsche Bauchemie e.V. (German Association for construction chemicals)". Sikafloor-262 AS N is the main wearing course of the Sikafloor Multidur ES-24 ECF System. - Electrostatic conductive
- Good chemical and mechanical resistance
- Easy to clean
- Economical
- Liquid proof
- Semi-gloss finish
- Slip resistant surface possible
|
Usage Sikafloor-262 AS N is used as: - Decorative and protective electrostatic conductive self-smoothing system for concrete or cement screeds with normal up to medium heavy wear.
- Suitable as a wearing course in industries, such as automotive, electronics and pharmaceutical manufacturing, storage facilities and warehouses.
- Particularly suitable for areas with sensitive electronic equipment e.g. CNC machinery, computer rooms , aircraft maintenance sheds, battery-charging rooms and areas subjected to high explosion risk
Advantages - Electrostatic conductive
- Good chemical and mechanical resistance
- Easy to clean
- Economical
- Liquid proof
- Semi-gloss finish
- Slip resistant surface possible
Packaging Part A | 21 kg containers | Part B | 4 kg containers | Part A + B | 25 kg ready to mix units |
Colour Resin - part A | coloured, liquid | Hardener - part B | transparent, liquid |
Almost unlimited choice of colour shades.
Due to the nature of carbon fibres providing the conductivity, it is not possible to achieve exact colour matching. With very bright colours (such as yellow and orange), this effect is increased. Under direct sun light there may be some discoloration and colour variation, this has no influence on the function and performance of the coating. |
Technical Information Shore D Hardness ~77 (3 days / +23°C) | (DIN 53 505) |
Abrasion Resistance Resin (filled with F34): 100 mg* (CS 10/1000/1000) (7 days / +23°C) | (DIN 53 109 (Taber Abraser Test)) |
Compressive Strength Resin: ~ 80 N/mm² (filled 1:0.3 with F34) (28 days / +23°C) | (EN 196-1) |
Flexural Strength Resin: ~ 40 N/mm² (filled 1:0.3 with F34*) (28 days / +23°C) | (EN 196-1) |
Tensile Adhesion Strength > 1.5 N/mm² (failure in concrete) | (ISO 4624) |
Chemical Resistance Resistant to many chemicals. Please contact Sika technical service.
Thermal Resistance Exposure* | Dry heat | Permanent | +50°C | Short-term max. 7 d | +80°C | | Short-term max. 2 h | +100°C |
Short-term moist/wet heat* up to +80°C where exposure is only occasional (i.e. during steam cleaning etc.)
*No simultaneous chemical and mechanical exposure.
Electrostatic Behaviour Resistance to ground1) | Rg < 109 Ω | Typical average resistance to ground2) | Rg ≤ 106 Ω |
1) This product fulfils the requirements of ATEX 137
2) Readings may vary, depending on ambient conditions (i.e. temperature, humidity) and measurement equipment.
|
Application Information Mixing Ratio Part A : part B = 84 : 16 (by weight) Ambient Air Temperature +10°C min. / +30°C max. Relative Air Humidity 80% r.h. max. Dew Point Beware of condensation!
The substrate and uncured floor must be at least 3°C above dew point to reduce the risk of condensation or blooming on the floor finish. Substrate Temperature +10°C min. / +30°C max. Substrate Moisture Content < 4% pbw moisture content.
Test method: Sika-Tramex meter, CM - measurement or Oven-dry-method. No rising moisture according to ASTM (Polyethylene-sheet). Pot Life Temperatures | Time | +10°C | ~ 40 minutes | +20°C | ~ 25 minutes | | +30°C | ~ 15 minutes |
Applied Product Ready for Use Temperature | Foot traffic | Light traffic | Full cure | +10°C | ~ 30 hours | ~ 5 days | ~ 10 days | +20°C | ~ 24 hours | ~ 3 days | ~ 7 days | +30°C | ~ 16 hours | ~ 2 days | ~ 5 days |
Note: Times are approximate and will be affected by changing ambient conditions. |
The above design is only a sample of the options available, for reference purposes only. Our policy of continuous improvement may result in a change of specifications without notice. If any discrepencies might be between the data sheet values and standards, we reserve the rights to make technical changes. Our company will not be held responsible, as all or any of pictures, drawings, weights and dimensions details or other elements in this document are only indicative and must not be considered contractual. Contact our sales team for other specifications or custom made products.
Contact our sales team for other specifications or custom made products.
