Electrostatic dissipative epoxy floor coating Sikafloor-2350 ESD is a 2-part self smoothing coloured electrostatic dissipative epoxy resin floor coating. - Reliable long term conductivity
- Meets ESD requirements
- Low VOC emissions
- Abrasion resistant
- Low odour during application
- High mechanical resistance
|
Usage The Product can be used as a: Smooth electrostatically conductive floor covering Please note: - The Product may only be used for interior applications.
- The Product may only be used by experienced professionals.
Advantages - Reliable long term conductivity
- Meets ESD requirements
- Low VOC emissions
- Abrasion resistant
- Low odour during application
- High mechanical resistance
Packaging | Container Part A | 24,6 kg | | Container Part B | 5,4 kg | | Container Part A + Part B | 30 kg |
Colour | Part A | coloured liquid | | Part B | transparent liquid | | Cured product colour | Available in the approximate colours RAL 1014, RAL 3012, RAL 5024, RAL 6010, RAL 6020, RAL 6021, RAL 6027, RAL 6033, RAL 6034, RAL 7005, RAL 7015, RAL 7016, RAL 7030, RAL 7032, RAL 7035, RAL 7040, RAL 7047 |
Please contact Sika customer service for information on availability. Note: When the product is exposed to direct sunlight, there may be some discolouration and colour variation. This has no influence on the function and performance of the coating. |
Technical Information Shore D Hardness | ~80 (after 7 days at +23 °C) | (EN ISO 868) |
Abrasion Resistance | ~1.29 g, resin filled 20% with QS (H22/1000/1000) (af-ter 20 days at +23°C) | (EN ISO 5470-1) |
Compressive Strength | Cured 28 days at +23 °C | ~120 MPa |
Flexural Strength | Cured 28 days at +23 °C | ~30 MPa |
Tensile adhesion strength | > 1,5 N/mm² (failure in concrete) | (EN 1542) |
Electrostatic Behaviour | Resistance to ground | RG < 109 Ω This product fulfils the requirements of ATEX 137 |
| Typical average resistance to ground | RG ≤ 105 Ω to 106 Ω |
| Body voltage generation | < 100 V | | System Resistance (Person/Floor/footwear) | < 109 Ω |
Note: Measurement results can be affected by ESD clothing, ambient conditions, measurement equipment, cleanliness of the floor and the test personnel.
Thermal Resistance | Short-term, maximum 7 days | +60 °C |
IMPORTANT: No simultaneous mechanical and chemical strain While the product is exposed to temperatures up to +60 °C, do not also subject it to chemical and/or mechanical strain, as it may cause damage to the product.
|
Application Information Mixing Ratio | Part A : Part B (by weight) | 82 : 18 |
Product Temperature | Minimum | +15 °C | | Maximum | +30 °C |
Ambient Air Temperature | Minimum | +15 °C | | Maximum | +30 °C |
Relative Air Humidity 80 % r.h. max. Dew Point Beware of condensation. The substrate and uncured applied product must be at least +3 °C above dew point to reduce the risk of condensation or blooming on the surface of the applied product. Low temperatures and high humidity conditions increase the probability of blooming. Substrate Temperature | Minimum | +15 °C | | Maximum | +30 °C |
Substrate Moisture Content < 4 % parts by weight (Sika Tramex moisture meter) No rising moisture (ASTM D4263, polyethylene sheet) The substrate must be visibly dry with no standing water. Pot Life | +10 °C | 40 minutes | | +20 °C | 25 minutes | | +30 °C | 15 minutes |
Applied Product Ready for Use | Temperature | Foot traffic | Light traffic | Full cure | | +15 °C | ~48 hours | ~3 days | ~7 days | | +20 °C | ~24 hours | ~48 hours | ~4 days | | +30 °C | ~16 hours | ~36 hours | ~3 days |
Note:Times are approximate and will be affected by changing ambient conditions, particularly temperature and relative humidity. |
The above design is only a sample of the options available, for reference purposes only. Our policy of continuous improvement may result in a change of specifications without notice. If any discrepencies might be between the data sheet values and standards, we reserve the rights to make technical changes. Our company will not be held responsible, as all or any of pictures, drawings, weights and dimensions details or other elements in this document are only indicative and must not be considered contractual. Contact our sales team for other specifications or custom made products.
Contact our sales team for other specifications or custom made products.
